Atlanta Electrical Services
Extension cords running across the floor. Power strips daisy-chained behind the couch. A single outlet on a 15-foot wall. If this sounds like your house, you're not alone. Most Atlanta homes -- especially those built before 2000 -- don't have enough outlets for the way we live now. Between phones, laptops, kitchen appliances, TVs, and smart home devices, the demand has outpaced what builders originally wired.
JD Works Electrical installs new outlets and switches across metro Atlanta. Standard 120V outlets, GFCI protection for wet areas, USB-equipped outlets for charging stations, 240V circuits for dryers and ranges, dimmer switches, smart switches, and everything in between. Jordan Jones handles every job with the same attention to detail whether it's a single outlet addition or a whole-house upgrade.
We also fix the things previous homeowners or handymen got wrong. Outlets with no ground. Switches wired to the wrong fixture. Two-prong receptacles in a house that should've been updated years ago. Every outlet and switch we install meets current NEC code and Georgia building standards. No shortcuts.
Common Problems
If every outlet in your room has a power strip plugged into it, you're overloading circuits. That's a fire risk. Adding dedicated outlets spreads the load safely across your electrical system.
A small spark when you plug something in can be normal. Repeated sparking, discoloration, or warmth around an outlet is not. That means loose connections, damaged wiring, or an overloaded circuit. Get it checked.
Two-prong outlets mean there's no grounding. That's a safety issue for any device with a 3-prong plug and a real problem for surge-sensitive electronics like computers and TVs.
Kitchens, bathrooms, garages, and outdoor areas all require GFCI outlets by code. If your outlets in these areas don't have Test/Reset buttons, they're not protected. Water and electricity don't mix.
Home offices, charging stations, kitchen appliance garages. The average home today has 3x the electrical demand it had 30 years ago. Adding outlets where you actually need them makes everything easier.
Our Process
Step 01
We walk your home, identify where you need outlets or switches, check your panel capacity, and assess the existing wiring. You tell us what you plug in and where. We figure out what's needed.
Step 02
We provide a clear, itemized quote covering every outlet and switch. No per-hour billing surprises. Once approved, we schedule the work at a time that fits your calendar.
Step 03
We cut openings, run wiring, install boxes, mount devices, and test every outlet and switch. GFCI outlets get trip-tested. Dimmers get range-checked. Everything works before we pack up.
Common Questions
The National Electrical Code requires GFCI protection in bathrooms, kitchens (countertop outlets), garages, unfinished basements, crawl spaces, laundry areas, and all outdoor outlets. Georgia follows the NEC, so any new outlet installation in these areas must include GFCI protection. If your home was built before these codes were adopted, upgrading to GFCI is one of the smartest safety improvements you can make.
Yes. Older homes in areas like Inman Park, Virginia-Highland, and East Atlanta often have too few outlets. We add new outlets by running wire through wall cavities, attics, or crawl spaces. The approach depends on your home's construction. We aim for minimal wall damage and clean installations that look like they were always there.
A standard outlet installation typically runs $150 to $300 per outlet depending on accessibility and how far the wire needs to run. GFCI outlets cost slightly more due to the device itself. 240V outlets for appliances run $250 to $500 because they require heavier wire and a dedicated circuit. We provide exact pricing after seeing your setup.
It depends on the wiring. If a ground wire is present in the box but not connected, we can wire a proper 3-prong outlet. If there's no ground wire, we have two code-compliant options: run a new ground wire or install a GFCI outlet with a "No Equipment Ground" label. We never just swap the receptacle without addressing the grounding.
Smart switches let you control lights from your phone, set schedules, and use voice commands through Alexa or Google Home. They're worth it if you want convenience and energy savings. Most smart switches require a neutral wire in the switch box. Older homes sometimes lack this. We check your wiring, install the switch, and make sure it connects to your Wi-Fi and smart home system.
For a simple outlet or switch replacement, typically no. For new circuits, adding outlets to new locations, or installing 240V circuits, the City of Atlanta and most surrounding counties require a permit and inspection. We handle the permitting process so you don't have to worry about it.
More Services
Recessed lights, LED upgrades, dimmer switches, and custom lighting design for any room.
Learn MoreWhole-home surge protection to safeguard your electronics and appliances from power spikes.
Learn MoreNew fan installs, replacements, and fan-light combos with proper wiring and secure mounting.
Learn MoreWhat Our Customers Say
"Lost power in half the house on a Saturday night. Jordan answered the phone, walked us through some safety checks, and came out first thing Sunday morning. Found a failing breaker and had it replaced in under an hour. Lifesaver."
David & Lisa M.
Homeowners — Tucker, GA